Maximize contact area
The larger the contact area between the tip and the pad, the higher the heat transfer efficiency. Prefer “Flat/Chisel” over “Pointed”.
Procurement Guide
Choose the right soldering tip for the work
Use application, pad size, solder material, station type, delivery conditions, and after-sales requirements to build a clear purchasing decision.
0.8–1.2×tip width / pad diameter
30–50°Chigher for lead-free solder
±0.1 mmnominal manufacturing tolerance
6 monthswarranty period
Selection Rules
Start with the soldering task
Before reviewing the specific application scenarios below, please keep in mind three golden rules:
Size matching
Tip width should be approximately 0.8 to 1.2 times the pad diameter.
Temperature and heat capacity
Lead-free (SAC305) requires approx. 30~50°C higher than leaded (Sn63Pb37); multi-layer / ground pads need larger tips for adequate thermal mass.
Application Matrix
Match shape, size, temperature, and station
| Application | Recommended shape | Recommended Size | Recommended Temp | Recommended Station Type |
|---|---|---|---|---|
| Through-Hole Technology | Chisel/Bevel | Tip width 2.4~3.2mm | 360~380°C | Standard ceramic stations |
| Surface-Mount Devices (Chip/Resistor) | Knife / Bevel Chisel | Blade width 1.2~2.0mm | 340~360°C | Integrated smart stations |
| Multi-pin ICs / Connectors | Knife | Blade width 1.5~2.5mm | 340~370°C | High-frequency or high-power integrated |
| General Repair / Rework | Conical/Pointed | Tip dia. 0.5~1.6mm | 300~340°C | Universal portable stations |
| BGA Reballing / Pad Tinning | Knife / Special Scraper | Blade width 1.0~1.8mm | 330~360°C | Precision temperature-controlled stations |
| Automated Robotic Arms | Customized Flat / Chisel | Strictly match pad size | 340~380°C | Robot-specific controllers |
| Micro-soldering / Fine Pitch | Extra-fine Pointed / Micro Knife | Tip dia. 0.1~0.4mm | 280~320°C | Nano / Micro stations |
Shape & Station Matching
Detailed shape functions
| Shape | Code | Core Function | Best-Matched Equipment |
|---|---|---|---|
| Pointed | I / B / ILS | Precision spot soldering, ultra-small components, jumper wires. Lowest thermal mass | T12 / JBC C210 / C115 |
| Conical | B / BL | Universal, suitable for repair and general THT | 936 / Weller LT / goot RX/FX-888D |
| Chisel | D / BC / C | Most recommended all-rounder. Balances heat and precision | JBC C245 / T12 / 936/FX-888D |
| Knife | K/KU/SK | King of drag soldering. Uses surface tension to remove excess solder | JBC C245 / T12 / 936/FX-888D |
| Bevel | Suitable for larger pads, terminals, high-current contacts | 203H / 205H High Frequency Station |
| Solder Type | Tip Temp | Cautions |
|---|---|---|
| Leaded Solder | 300°C ~ 340°C | Suggest 315°C as a universal starting point |
| Lead-free Solder | 350°C ~ 390°C | When >380°C, shorten contact time (<3s) to prevent burns. |
| High-temp Solder | 400°C ~ 450°C | Must use high thermal mass tips (HF or large chisel) |
| Low-temp Paste / Wire | 260°C ~ 280°C | Commonly used for LED strips, FPC to prevent heat damage |
Special Scenario Notes
High Layer Count PCBs: Rapid heat dissipation; choose Type D or C, width ≥2.5mm; prefer High-Frequency or high-wattage JBC.
Ultra-fine Pitch: Lower temp (300-320°C), use K-type tip with liquid flux for dragging. Must use T12/JBC C210 level stations.
Robotic Automation: Automation demands strict dimensional consistency (±0.05mm) and tin-wetting position repeatability.
Purchase Conditions
Plan the order from sample to delivery
| Product Category | Standard MOQ | Custom MOQ |
|---|---|---|
| Standard Series (900M/T12/LT/ET etc.) | 100PCS/per model | 200PCS/per model |
| High-Frequency Series (200/500 Series etc.) | 100PCS/per model | 500pcs/per model |
| Robotic Tips (Apollo/UNIX etc.) | 50PCS/per model | 100PCS/per model |
| Order Type | Standard Lead Time | Express Service |
|---|---|---|
| In-stock Standard Products | 3-5 working days after payment received | 1-2 working days (expediting fee applies) |
| Custom Orders | 15-25 working days after sample approval & deposit receipt | 15 working days |
| Bulk Orders (>5000 PCS） | 25-35 working days | subject to negotiation |
| Packaging Layer | Material | Function |
|---|---|---|
| Inner Pack | Anti-static PE bag | Dustproof & ESD protection |
| Buffer Layer | EPE foam | Fix the tips, prevent collision and abrasion |
| Outer Carton | Standard 5-layer corrugated export carton | Strong compression resistance |
Payment & Shipping
T/T (Telegraphic Transfer)：30% deposit + 70% balance before shipment。
International Express (DHL / FedEx / UPS / TNT)：Suitable for samples or small goods <100KG. Transit time: 3-7 days.
Air Freight：Suitable for urgent goods 100KG-500KG. Transit: 5-10 days.
Sea Freight：Suitable for bulk orders (>500KG). Transit: 15-35 days.
Buyer's Forwarder：We accept buyer's designated forwarder for door pick-up (EXW/FOB terms).
Lead times are automatically extended during national holidays (e.g., National Day, Chinese New Year). Please inform us in advance if you need OEM packaging (neutral packaging / customer brand labels / custom blister card printing).
After-Sales Responsibility & Warranty
Keep quality responsibilities clear
| Warranty Period | Scope of Responsibility |
|---|---|
| 6 months from the date of shipment | Manufacturing defects such as plating peeling or pitting, excluding human damage. |
| RMA Process | If quality issues arise, please provide HD pictures/videos as evidence within 7 days of receipt. Upon confirmation by our engineers, we will deduct the amount or resend the quantity in the next order. |
We are NOT responsible for:
1. Wrong model selection (e.g., using T12 tips on a 936 station).
2. Damage caused by overheating, dropping, or corrosive flux usage.
3. Normal wear and tear (plating naturally wears out over time).
Brand Product Information
Open only the product family you need
Expand a brand to view the detailed product information table. Product dimensions are nominal values. Manufacturing tolerance is ±0.1mm. Plating thickness (Iron/Nickel/Chrome) may slightly affect final outer diameters.
HakkoView detailed product information+
| Series | Model | Tip Shape | Dimensions | Primary Applications | Compatible Equipment |
|---|---|---|---|---|---|
| View Hakko detailed product information | |||||
| 900M | 900M-T-K | Knife（K） | Blade 5mm / L 43mm | Drag soldering for QFP/PLCC ICs | 936,937，FX-888D/FX-888 |
| 900M | 900M-T-SK | Knife（SK） | Blade 3.5mm / L 43mm | Drag soldering for QFP/PLCC ICs | 936,937，FX-888D/FX-888 |
| 900M | 900M-T-I | Pointed（I） | Tip φ0.2mm / L 43mm | Micro-soldering (0201, mobile PCBs) | 936,937，FX-888D/FX-888 |
| 900M | 900M-T-B | Conical (B) | Tip φ1.0mm / L 43mm | General through-hole soldering | 936,937，FX-888D/FX-888 |
| 900M | 900M-T-0.8D | Flat Chisel (D) | Width 0.8mmL 43mm | Large ground pads, heavy wires | 936,937，FX-888D/FX-888 |
| 900M | 900M-T-1.2D | Flat Chisel (D) | Width 1.2mmL 43mm | Fine-pitch SMD soldering | 936,937，FX-888D/FX-888 |
| 900M | 900M-T-1.6D | Flat Chisel (D) | Width 1.6mmL 43mm | General bench repair | 936,937，FX-888D/FX-888 |
| 900M | 900M-T-2.4D | Flat Chisel (D) | Width 2.4mmL 43mm | Fine-pitch SMD soldering | 936,937，FX-888D/FX-888 |
| 900M | 900M-T-1C | Bevel (C) | φ1.0mm | Fine SMD | 936,937，FX-888D/FX-888 |
| 900M | 900M-T-2C | Bevel (C) | φ2.0mm | General SMD | 936,937，FX-888D |
| 900M | 900M-T-3C | Bevel (C) | φ3.0mm | Larger pads | 936,937，FX-888D |
| 900M | 900M-T-4C | Bevel (C) | φ4.0mm | Larger pads | 936,937，FX-888D |
| T18 | T18-B | Conical (B) | Tip φ1.0mm / L 40.5mm | General through-hole soldering | FX-888D |
| T18 | T18-BL | Conical (B) | Tip φ0.4mm / L 48.5mm | General through-hole soldering | FX-888D |
| T18 | T18-I | Pointed（I） | Tip φ0.2mm / L 40.5mm | Micro-soldering (0201, mobile PCBs) | FX-888D |
| T18 | T18-C1 | Bevel (C) | φ1.0mm | Fine SMD | FX-888D |
| T18 | T18-C2 | Bevel (C) | φ2.0mm | General SMD | FX-888D |
| T18 | T18-C3 | Bevel (C) | φ3.0mm | Larger pads | FX-888D |
| T18 | T18-C4 | Bevel (C) | φ4.0mm | Larger pads | FX-888D |
| T18 | T18-D08 | Flat Chisel (D) | Width 0.8mm | Fine-pitch SMD soldering | FX-888D |
| T18 | T18-D12 | Flat Chisel (D) | Width 1.2mm | Fine-pitch SMD soldering | FX-888D |
| T18 | T18-D16 | Flat Chisel (D) | Width 1.6mm | General bench repair | FX-888D |
| T18 | T18-D24 | Flat Chisel (D) | Width 2.4mm | Fine-pitch SMD soldering | FX-888D |
| T18 | T18-D32 | Flat Chisel (D) | Width 3.2mm | Larger pads, connectors | FX-888D |
| T18 | T18-K | Knife（K） | Blade 5mm / L 40mm | Drag soldering for QFP/PLCC ICs | FX-888D |
| T18 | T18-BR02 | Bent tip shape | φ0.2mm | Micro-soldering (0201, mobile PCBs) | FX-888D |
| T18 | T18-SK | Knife（SK） | Blade 3.5mm / L 40mm | Drag soldering for QFP/PLCC ICs | FX-888D |
| T18 | T18-CF1 | Bevel (CF) | φ1.0mm | Fine SMD | FX-888D |
| T18 | T18-CF2 | Bevel (CF) | φ2.0mm | General SMD | FX-888D |
| T18 | T18-CF3 | Bevel (CF) | φ3.0mm | Larger pads | FX-888D |
| T18 | T18-CF4 | Bevel (CF) | φ4.0mm | Larger pads | FX-888D |
| T12 | T12-K | Knife（K） | Blade 5mm / L 31mm | High-thermal-demand SMD dragging | FX-951，T12 Station |
| T12 | T12-KU | Knife（SK） | Blade 3mm / L 28mm | High-thermal-demand SMD dragging | FX-951，T12 Station |
| T12 | T12-BC2 | Bevel Chisel (BC) | φ2.0mm / L 28mm | Universal SMD & through-hole | FX-951，T12 Station |
| T12 | T12-I | Pointed（I） | Tip φ0.2mm / L 26mm | Micro-soldering (0201, mobile PCBs) | FX-951，T12 Station |
| T12 | T12-BL | Conical | Tip φ0.8mm / L 29mm | General through-hole soldering | FX-951，T12 Station |
| T12 | T12-D24 | Flat Chisel (D) | Width 2.4mm / L 28mm | Fine-pitch SMD soldering | FX-951，T12 Station |
| T12 | T12-ILS | Pointed (I) | Tip φ0.4mm / L 26mm | Fine SMD, BGA rework | FX-951，T12 Station |
| T12 | T12-D08 | Flat Chisel (D) | Width 0.8mm / L 28mm | Fine-pitch SMD soldering | FX-951，T12 Station |
| T12 | T12-D52 | Flat Chisel (D) | Width 5.2mm / L 44mm | Heavy-duty soldering | FX-951，T12 Station |
| T32 | T32-K | Knife（K） | Blade 5mm / L 20mm | Drag soldering for QFP/PLCC ICs | FX-890 Station |
| T32 | T32-KU | Knife（SK） | Blade 3mm / L 20mm | Drag soldering for QFP/PLCC ICs | FX-890 Station |
| T32 | T32-BC3 | Bevel Chisel (BC) | φ3.0mm / L 20mm | Universal SMD & through-hole | FX-890 Station |
| T32 | T32-BC2 | Bevel Chisel (BC) | φ2.0mm/L 21mm | General SMD | FX-890 Station |
| T32 | T32-BC1 | Bevel Chisel (BC) | φ1.0mm/L 20mm | Fine SMD | FX-890 Station |
| T32 | T32-D32 | Flat Chisel (D) | Width 3.2mm | Larger pads, connectors | FX-890 Station |
| T32 | T32-D24 | Flat Chisel (D) | Width 2.4mm | Fine-pitch SMD soldering | FX-890 Station |
| T32 | T32-D12 | Flat Chisel (D) | Width 1.2mm | Fine-pitch SMD soldering | FX-890 Station |
| T32 | T32-B | Conical (B) | Tip φ1.0mm / L 21mm | General through-hole soldering | FX-890 Station |
| T32 | T32-I | Pointed (I) | Tip φ0.2mm / L 21mm | Fine SMD, BGA rework | FX-890 Station |
| T32 | T32-J02 | Bent tip shape | φ0.2mm | Micro-soldering (0201, mobile PCBs) | FX-890 Station |
| T32 | T32-D16 | Flat Chisel (D) | Width 1.6mm / L 21mm | General bench repair | FX-890 Station |
WellerView detailed product information+
| Series | Model | Tip Shape | Dimensions | Primary Applications | Compatible Equipment |
|---|---|---|---|---|---|
| View Weller detailed product information | |||||
| ET | ET-A | Chisel | 1.6×0.7mm / L 34.5mm | General bench repair | WE1010/WES50/WES51/WESD51 Station，WSP50/WSP51 handle |
| ET | ET-B | Chisel | 2.4×0.8mm / L 34.5mm | Standard through-hole | WE1010/WES50/WES51/WESD51 Station，WSP50/WSP51 handle |
| ET | ET-L | Chisel | 2.0×1.0mm / L 43.5mm | General through-hole | WE1010/WES50/WES51/WESD51 Station，WSP50/WSP51 handle |
| ET | ET-C | Chisel | 3.2×0.8mm / L 34.5mm | Larger pads, connectors | WE1010/WES50/WES51/WESD51 Station，WSP50/WSP51 handle |
| ET | ET-D | Chisel | 4.2×0.8mm / L 41mm | Large ground pads | WE1010/WES50/WES51/WESD51 Station，WSP50/WSP51 handle |
| ET | ET-P | Conical | φ0.8mm / L 34.5mm | Fine SMD soldering | WE1010/WES50/WES51/WESD51 Station，WSP50/WSP51 handle |
| ET | ET-R | Chisel | 1.6×0.7mm / L 41mm | SMD components | WE1010/WES50/WES51/WESD51 Station，WSP50/WSP51 handle |
| ET | ET-KN | Knife（K） | Blade 5mm / L 35mm | High-thermal-demand SMD dragging | WE1010/WES50/WES51/WESD51 Station，WSP50/WSP51 handle |
| ET | ET-CC | Bevel Chisel (BC) | φ3.2mm / L 34.5mm | Universal SMD & through-hole | WE1010/WES50/WES51/WESD51 Station，WSP50/WSP51 handle |
| ET | ET-BB | Bevel Chisel (BC) | φ2.4mm / L 34.5mm | Universal SMD & through-hole | WE1010/WES50/WES51/WESD51 Station，WSP50/WSP51 handle |
| ET | ET-K | Chisel | Width 1.2mm / L 43.5mm | Fine-pitch SMD soldering | WE1010/WES50/WES51/WESD51 Station，WSP50/WSP51 handle |
| ET | ET-S | Conical | φ0.4mm / L 43.5mm | Fine SMD soldering | WE1010/WES50/WES51/WESD51 Station，WSP50/WSP51 handle |
| LT | LT-A | Chisel | Width 1.6mm / L 13mm | General bench repair | WSD81/WT1013/WT1012 Series Station，WP80/WSP80/WXP80 handle |
| LT | LT-B | Chisel | Width 2.4mm / L 13mm | Standard through-hole | WSD81/WT1013/WT1012 Series Station，WP80/WSP80/WXP80 handle |
| LT | LT-C | Chisel | Width 3.2mm / L 13mm | Larger pads, connectors | WSD81/WT1013/WT1012 Series Station，WP80/WSP80/WXP80 handle |
| LT | LT-D | Chisel | Width 4.2mm / L 13mm | Large ground pads | WSD81/WT1013/WT1012 Series Station，WP80/WSP80/WXP80 handle |
| LT | LT-BB45° | Bevel (C) | φ2.4mm / L 17mm | General SMD | WSD81/WT1013/WT1012 Series Station，WP80/WSP80/WXP80 handle |
| LT | LT-CC45° | Bevel (C) | φ3.0mm/L 17mm | Larger pads | WSD81/WT1013/WT1012 Series Station，WP80/WSP80/WXP80 handle |
| LT | LT-DD | Bevel (C) | φ4.0mm/L 17mm | Larger pads | WSD81/WT1013/WT1012 Series Station，WP80/WSP80/WXP80 handle |
| LT | LT-T | Conical | φ0.6mm / L 13mm | Fine SMD soldering | WSD81/WT1013/WT1012 Series Station，WP80/WSP80/WXP80 handle |
| LT | LT-1 | Conical | φ0.25mm / L 13mm | Fine SMD soldering | WSD81/WT1013/WT1012 Series Station，WP80/WSP80/WXP80 handle |
| LT | LT-S | Conical | φ0.6mm / L 20mm | Fine SMD soldering | WSD81/WT1013/WT1012 Series Station，WP80/WSP80/WXP80 handle |
| LT | LT-1L | Conical | φ0.2mm / L 26mm | Fine SMD soldering | WSD81/WT1013/WT1012 Series Station，WP80/WSP80/WXP80 handle |
| LT | LT-KN | Knife（K） | Blade 5mm / L 17mm | High-thermal-demand SMD dragging | WSD81/WT1013/WT1012 Series Station，WP80/WSP80/WXP80 handle |
| LT | LT-KNS | Knife（SK） | Blade 3mm / L 12.5mm | High-thermal-demand SMD dragging | WSD81/WT1013/WT1012 Series Station，WP80/WSP80/WXP80 handle |
| LT | LT-K | Chisel | Width 1.2mm / L 20mm | General bench repair | WSD81/WT1013/WT1012 Series Station，WP80/WSP80/WXP80 handle |
| LT | LT-L | Chisel | Width 2.0mm / L 20mm | General bench repair | WSD81/WT1013/WT1012 Series Station，WP80/WSP80/WXP80 handle |
| LT | LT-M | Chisel | Width 3.2mm / L 20mm | Larger pads, connectors | WSD81/WT1013/WT1012 Series Station，WP80/WSP80/WXP80 handle |
| LT | LT-H | Chisel | Width 0.8mm / L 13mm | Fine-pitch SMD soldering | WSD81/WT1013/WT1012 Series Station，WP80/WSP80/WXP80 handle |
| LT | LT-O | Chisel | Tip φ1.0mm / L 17mm | General through-hole soldering | WSD81/WT1013/WT1012 Series Station，WP80/WSP80/WXP80 handle |
| XT | XT-0 | Conical (B) | φ1.0mm / L 37mm | General through-hole soldering | WSD121/WSD120 Station |
| XT | XT-KN | Knife（K） | Blade 5mm / L 32mm | Drag soldering for QFP/PLCC ICs | WSD121/WSD120 Station |
| XT | XT-A | Flat Chisel (D) | Width 1.6mm / L 37mm | General bench repair | WSD121/WSD120 Station |
| XT | XT-B | Flat Chisel (D) | Width 2.4mm / L 37mm | General bench repair | WSD121/WSD120 Station |
| XT | XT-C | Flat Chisel (D) | Width 3.2mm /L 37mm | Larger pads, connectors | WSD121/WSD121 Station |
| XT | XT-D | Flat Chisel (D) | Width 4.6mm / L 37mm | Large ground pads | WSD121/WSD122 Station |
| XT | XT-E | Flat Chisel (D) | Width 5.9mm / L 37mm | Large ground pads | WSD121/WSD123 Station |
| XT | XT-H | Flat Chisel (D) | Width 0.8mm / L 37mm | Fine-pitch SMD soldering | WSD121/WSD124 Station |
| XT | XT-M | Flat Chisel (D) | Width 3.2mm / L 40mm | Larger pads, connectors | WSD121/WSD125 Station |
| XT | XT-AA | Bevel (C) | φ1.6mm/L 37mm | Fine SMD | WSD121/WSD126 Station |
| XT | XT-BB | Bevel (C) | φ2.4mm/L 37mm | General SMD | WSD121/WSD127 Station |
| XT | XT-CC | Bevel (C) | φ3.2mm/L 37mm | Larger pads | WSD121/WSD128 Station |
| XT | XT-F | Bevel (C) | φ1.2mm/L 37mm | Fine SMD | WSD121/WSD129 Station |
| MTX | MXT-1 | Conical | φ0.25mm / L 33mm | Fine SMD soldering | WSD71 Station，WP70 handle |
| MTX | MXT-O | Conical (B) | φ1.0mm / L 33mm | General through-hole soldering | WSD71 Station，WP70 handle |
| MTX | MXT-KN | Knife（K） | Blade 4.7mm / L 33mm | Drag soldering for QFP/PLCC ICs | WSD71 Station，WP71 handle |
| MTX | MXT-A | Flat Chisel (D) | Width 1.6mm / L 33mm | General bench repair | WSD71 Station，WP72 handle |
| MTX | MXT-B | Flat Chisel (D) | Width 2.4mm / L 33mm | General bench repair | WSD71 Station，WP73 handle |
| MTX | MXT-C | Flat Chisel (D) | Width 3.2mm /L 33mm | Larger pads, connectors | WSD71 Station，WP74 handle |
| MTX | MXT-H | Flat Chisel (D) | Width 0.8mm / L 33mm | Fine-pitch SMD soldering | WSD71 Station，WP75 handle |
| MTX | MXT-BB | Bevel (C) | φ2.4mm/L 33mm | General SMD | WSD71 Station，WP76 handle |
| MTX | MXT-CC | Bevel (C) | φ3.2mm/L 37mm | Larger pads | WSD71 Station，WP77 handle |
| LHT | LHT-C | Flat Chisel (D) | Width 3.2mm /L 25mm | Larger pads, connectors | WSD151/WSP150 Station |
| LHT | LHT-D | Flat Chisel (D) | Width 4.7mm / L 25mm | Larger pads | WSD151/WSP150 Station |
| LHT | LHT-E | Flat Chisel (D) | Width 6.7mm / L 25mm | Larger pads | WSD151/WSP150 Station |
| LHT | LHT-F | Flat Chisel (D) | Width 9.3mm / L 25mm | Larger pads | WSD151/WSP150 Station |
| XHT | XHT-O | Conical (B) | φ2.0mm / L 51.5mm | Robotic soldering | Weller 200W Robot Stations/WP200 Soldering Handle |
| XHT | XHT-CC | Bevel (C) | φ3.2mm/L 51.5mm | Robotic soldering | Weller 200W Robot Stations/WP200 Soldering Handle |
| XHT | XHT-DD | Bevel (C) | φ5.0mm/L 51.5mm | Robotic soldering | Weller 200W Robot Stations/WP200Soldering Handle |
| XHT | XHT-C | Flat Chisel (D) | Width 3.2mm /L 51.5mm | Robotic soldering | Weller 200W Robot Stations/WP200 Soldering Handle |
| XHT | XHT-D | Flat Chisel (D) | Width 5.0mm / L 51.5mm | Robotic soldering | Weller 200W Robot Stations/WP200 Soldering Handle |
| XHT | XHT-E | Flat Chisel (D) | Width 7.6mm /L 51.5mm | Robotic soldering | Weller 200W Robot Stations/WP200 Soldering Handle |
| XHT | XHT-F | Flat Chisel (D) | Width 9.3mm / L 51.5mm | Robotic soldering | Weller 200W Robot Stations/WP200 Soldering Handle |
JBCView detailed product information+
| Series | Model | Tip Shape | Dimensions | Primary Applications | Compatible Equipment |
|---|---|---|---|---|---|
| View JBC detailed product information | |||||
| C245 | C245-939 | Knife（K） | Blade 5mm | High-thermal-demand SMD dragging | CD/CDE/LC/D/DDSE/RMSE/BT Series Station，T245 handle |
| C245 | C245-906 | Flat Chisel (D) | 1.2×0.7mm | General bench repair | CD/CDE/LC/D/DDSE/RMSE/BT Series Station，T245 handle |
| C245 | C245-903 | Conical (B) | Tip φ1.0mm | General through-hole soldering | CD/CDE/LC/D/DDSE/RMSE/BT Series Station，T245 handle |
| C245 | C245-056 | Bevel (C) | φ3.5mm | Larger pads | CD/CDE/LC/D/DDSE/RMSE/BT Series Station，T245 handle |
| C210 | C210-018 | Knife（K） | φ3.4mm*0.3mm | High-thermal-demand SMD dragging | CD/DI/DDE/DME/DDPE Series Station，T210 handle |
| C210 | C210-021 | Chisel | Width 0.6mm | Fine-pitch SMD soldering | CD/DI/DDE/DME/DDPE Series Station，T210 handle |
| C115 | C115-222 | Chisel | Width 1.6mm | General bench repair | NANE/NASE/CDN Series Station，NT115 handle |
QUICKView detailed product information+
| Series | Model | Tip Shape | Dimensions | Primary Applications | Compatible Equipment |
|---|---|---|---|---|---|
| View QUICK detailed product information | |||||
| 200 | 200-K | Knife（K） | Blade 4.7mm / L 31.5mm | Drag soldering for QFP/PLCC ICs | 203H Station |
| 200 | 200-B | Conical (B) | Tip φ1.0mm / L 30.5mm | General through-hole soldering | 203H Station |
| 200 | 200-1C | Bevel (C) | φ1.0mm | Fine SMD | 203H Station |
| 200 | 200-2C | Bevel (C) | φ2.0mm | General SMD | 203H Station |
| 200 | 200-3C | Bevel (C) | φ3.0mm | Larger pads | 203H Station |
| 200 | 200-4C | Bevel (C) | φ4.0mm | Larger pads | 203H Station |
| 200 | 200-I | Pointed (I) | Tip φ0.2mm | Micro-soldering | 203H Station |
| 200 | 200-0.8D | Flat Chisel (D) | Width 0.8mm | Fine-pitch SMD | 203H Station |
| 200 | 200-1.2D | Flat Chisel (D) | Width 1.2mm | General bench repair | 203H Station |
| 200 | 200-1.6D | Flat Chisel (D) | Width 1.6mm | General bench repair | 203H Station |
| 200 | 200-2.4D | Flat Chisel (D) | Width 2.4mm | General through-hole | 203H Station |
| 200 | 200-3.2D | Flat Chisel (D) | Width 3.2mm | General through-hole | 203H Station |
| 500 | 500-B | Conical (B) | Tip φ1.0mm / L 38mm | General through-hole soldering | 205H Station |
| 500 | 500-K | Knife（K） | Blade 7.5mm / L 40mm | Drag soldering for QFP/PLCC ICs | 205H Station |
| 500 | 500-SK | Knife（SK） | Blade 5mm / L 31.5mm | Drag soldering for QFP/PLCC ICs | 205H Station |
| 500 | 500-2C | Bevel (C) | φ2.0mm | General SMD | 205H Station |
| 500 | 500-3C | Bevel (C) | φ3.0mm | Larger pads | 205H Station |
| 500 | 500-4C | Bevel (C) | φ4.0mm | Larger pads | 205H Station |
| 500 | 500-5C | Bevel (C) | φ5.0mm | Larger pads | 205H Station |
| 500 | 500-6C | Bevel (C) | φ6.0mm | Larger pads | 205H Station |
| 500 | 500-8C | Bevel (C) | φ8.0mm | Larger pads | 205H Station |
| 500 | 500-3.5D | Flat Chisel (D) | Width 3.5mm | Large ground pads | 205H Station |
| 500 | 500-4.2D | Flat Chisel (D) | Width 4.2mm | Large ground pads | 205H Station |
| 500 | 500-5D | Flat Chisel (D) | Width 5.0mm | Large ground pads | 205H Station |
| 500 | 500-6D | Flat Chisel (D) | Width 6.0mm | Large ground pads | 205H Station |
| 500 | 500-7D | Flat Chisel (D) | Width 7.0mm | Large ground pads | 205H Station |
| 500 | 500-8D | Flat Chisel (D) | Width 8.0mm | Large ground pads | 205H Station |
| 911G | 911G-20D | Flat Chisel (D) | Width 2.0mm / L 72mm | Robotic soldering | QUICK Soldering Robot |
| 911G | 911G-30D | Flat Chisel (D) | Width 3.0mm / L 72mm | Robotic soldering | QUICK Soldering Robot |
| 911G | 911G-40D | Flat Chisel (D) | Width 4.0mm / L 72mm | Robotic soldering | QUICK Soldering Robot |
| 911G | 911G-20DV1 | Single-sided V-groove | Width 2.0mm | Robotic soldering | QUICK Soldering Robot |
| 911G | 911G-30DV1 | Single-sided V-groove | Width 3.0mm | Robotic soldering | QUICK Soldering Robot |
| 911G | 911G-40DV1 | Single-sided V-groove | Width 4.0mm | Robotic soldering | QUICK Soldering Robot |
| 911G | 911G-30DV2 | Double-sided V-groove | Width 3.0mm | Robotic soldering | QUICK Soldering Robot |
| 911G | 911G-40DV2 | Double-sided V-groove | Width 4.0mm | Robotic soldering | QUICK Soldering Robot |
| 911G | 911G-30PC | Bevel Chisel (BC) | φ3.0mm | Robotic soldering | QUICK Soldering Robot |
| 911G | 911G-40PC | Bevel Chisel (BC) | φ4.0mm | Robotic soldering | QUICK Soldering Robot |
GooTView detailed product information+
| Series | Model | Tip Shape | Dimensions | Primary Applications | Compatible Equipment |
|---|---|---|---|---|---|
| PX | PX-2RT-5K | Knife（K） | Blade 5mm / L 52mm | Drag soldering for QFP/PLCC ICs | PX-338/335/201 |
| PX | PX-2RT-2C | Bevel (C) | φ2.0mm | General SMD | PX-338/335/201 |
| PX | PX-2RT-3C | Bevel (C) | φ3.0mm | Larger pads | PX-338/335/201 |
| PX | PX-2RT-5C | Bevel (C) | φ5.0mm | Larger pads | PX-338/335/201 |
| PX | PX-2RT-SB | Conical (B) | Tip φ0.3mm / L 52mm | Fine SMD soldering | PX-338/335/201 |
| PX | PX-2RT-B | Conical (B) | Tip φ0.5mm / L 52mm | Fine SMD soldering | PX-338/335/201 |
| PX | PX-2RT-BC | Bevel Chisel (BC) | φ1.0mm | Fine SMD | PX-338/335/201 |
| PX | PX-2RT-2D | Flat Chisel (D) | Width 2.0mm | General through-hole | PX-338/335/201 |
| PX | PX-2RT-3D | Flat Chisel (D) | Width 3.0mm | General through-hole | PX-338/335/201 |
| PX | PX-2RT-4D | Flat Chisel (D) | Width 4.0mm | Large ground pads | PX-338/335/201 |
| PX | PX-2RT-5D | Flat Chisel (D) | Width 5.0mm | Large ground pads | PX-338/335/201 |
| RX | RX-80HRT-0.8D | Flat Chisel (D) | Width 0.8mm | Fine-pitch SMD | GOOT Soldering iron |
| RX | RX-80HRT-1.2D | Flat Chisel (D) | Width 1.2mm | General bench repair | GOOT Soldering iron |
| RX | RX-80HRT-1.6D | Flat Chisel (D) | Width 1.6mm | General bench repair | GOOT Soldering iron |
| RX | RX-80HRT-2.4D | Flat Chisel (D) | Width 2.4mm | General through-hole | GOOT Soldering iron |
| RX | RX-80HRT-3.2D | Flat Chisel (D) | Width 3.2mm | Large ground pads | GOOT Soldering iron |
| RX | RX-80HRT-5.4D | Flat Chisel (D) | Width 5.4mm | Large ground pads | GOOT Soldering iron |
| RX | RX-80HRT-3K | Knife（K） | Blade 3mm / L 45mm | Drag soldering for QFP/PLCC ICs | GOOT Soldering iron |
| RX | RX-80HRT-3KU | Knife（K） | Blade 3mm*1.2mm / L 45mm | Drag soldering for QFP/PLCC ICs | GOOT Soldering iron |
| RX | RX-80HRT-4.5K | Knife（K） | Blade 4.5mm / L 45mm | Drag soldering for QFP/PLCC ICs | GOOT Soldering iron |
| RX | RX-80HRT-SI | Pointed（I） | Tip φ0.2mm | Micro-soldering (0201, mobile PCBs) | GOOT Soldering iron |
| RX | RX-80HRT-SB | Conical (B) | Tip φ0.3mm | Fine SMD soldering | GOOT Soldering iron |
| RX | RX-80HRT-LB | Conical (B) | Tip φ0.8mm /L 36mm | Fine SMD soldering | GOOT Soldering iron |
| RX | RX-80HRT-B | Conical (B) | Tip φ0.3mm /L 31.5mm | Fine SMD soldering | GOOT Soldering iron |
| RX | RX-80HRT-2B | Conical (B) | Tip φ0.6mm /L 31.5mm | Fine SMD soldering | GOOT Soldering iron |
| RX | RX-80HRT-1C | Bevel (C) | φ1.0mm | Fine SMD | GOOT Soldering iron |
| RX | RX-80HRT-1BC | Bevel Chisel (BC) | φ1.0mm | Fine SMD | GOOT Soldering iron |
| RX | RX-80HRT-2C | Bevel (C) | φ2.0mm | General SMD | GOOT Soldering iron |
| RX | RX-80HRT-2.3BC | Bevel Chisel (BC) | φ2.3mm | General SMD | GOOT Soldering iron |
| RX | RX-80HRT-3BC | Bevel Chisel (BC) | φ4.7mm | Larger pads | GOOT Soldering iron |
| RX | RX-80HRT-3C | Bevel (C) | φ3.0mm | Larger pads | GOOT Soldering iron |
| RX | RX-80HRT-4C | Bevel (C) | φ4.0mm | Larger pads | GOOT Soldering iron |
UNIXView detailed product information+
| Series | Model | Tip Shape | Dimensions | Primary Applications | Compatible Equipment |
|---|---|---|---|---|---|
| View UNIX detailed product information | |||||
| P | P2D-R | Flat Chisel (D) | Width 2.0mm | Robotic soldering | UNIX Robot Stations |
| P | P3D-R | Flat Chisel (D) | Width 3.0mm | Robotic soldering | UNIX Robot Stations |
| P | P4D-R | Flat Chisel (D) | Width 4.0mm | Robotic soldering | UNIX Robot Stations |
| P | P2D-S | Flat Chisel (D) | φ2.0mm, 0.5mm thick | Robotic soldering | UNIX Robot Stations |
| P | P3D-S | Flat Chisel (D) | φ3.0mm, 1mm thick | Robotic soldering | UNIX Robot Stations |
| P | P6D-S | Flat Chisel (D) | φ6.0mm, 1.1mm thick | Heavy robotic soldering | UNIX Robot Stations |
APOLLOView detailed product information+
| Series | Model | Tip Shape | Dimensions | Primary Applications | Compatible Equipment |
|---|---|---|---|---|---|
| View APOLLO detailed product information | |||||
| PAD | 20PAD07-B15 | Flat Chisel (D) | Width 2.0mm | Robotic soldering | TSUTSUMI Robot Station |
| PAD | 30PAD10-B30 | Flat Chisel (D) | Width 3.0mm | Robotic soldering | TSUTSUMI Robot Station |
TSUTSUMIView detailed product information+
| Series | Model | Tip Shape | Dimensions | Primary Applications | Compatible Equipment |
|---|---|---|---|---|---|
| View TSUTSUMI detailed product information | |||||
| SDG | TKH5-25SDG | Width 2.5mm | Robotic soldering | TSUTSUMI Robot Station | |
| SDG | TKH5-30SDG | Width 3.0mm | Robotic soldering | TSUTSUMI Robot Station | |
| SDG | TKH5-40SDG | Width 4.0mm | Robotic soldering | TSUTSUMI Robot Station | |
Can't find your exact OEM model?
We support full OEM/ODM non-standard customization – special angles, extra-long shafts, custom platings, and unique tip geometries.